Why is a white electrical wire connected to 2 black wires?
I just opened my ceiling light to replace it with another mount. I see a white wire connected to 2 black wires, is that right?
The middle switch controls this ceiling light.
electrical ceiling light
asked 5 hours ago
konyakkonyak
1084
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I just opened my ceiling light to replace it with another mount. I see a white wire connected to 2 black wires, is that right?
The middle switch controls this ceiling light.
electrical ceiling light
asked 5 hours ago
konyakkonyak
1084
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I just opened my ceiling light to replace it with another mount. I see a white wire connected to 2 black wires, is that right?
The middle switch controls this ceiling light.
electrical ceiling light
asked 5 hours ago
konyakkonyak
1084
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I just opened my ceiling light to replace it with another mount. I see a white wire connected to 2 black wires, is that right?
The middle switch controls this ceiling light.
electrical ceiling light
electrical ceiling light
asked 5 hours ago
konyakkonyak
1084
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 5 hours ago
konyakkonyak
1084
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 5 hours ago
konyakkonyak
1084
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 5 hours ago
konyakkonyak
1084
asked 5 hours ago
konyakkonyak
1084
1084
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
konyak is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
The cable with the white wire that's connected to the two black wires is a switch loop:
Normally wires with white insulation are used only for neutrals, but code makes an exception to allow for use of the white wire in a cable used as a switch loop as a hot rather than a neutral.
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
add a comment |
That is positional coding. It is very important data.
Wire colors in cable are standardized and do not vary. In any cable, if neutral is present, it must be the white. The most likely application for this is in a switch loop. If neutral is not present but an always-hot is, contemporary Code says white must be used for an always-hot. That's to make it easier to identify with a voltage tester. Newer code says white so used, must be marked with tape.
Once you have identified the neutral bundle (all white), a white in a non-neutral bundle is one of these. The fact this is in a lamp makes this most likely a switch loop.
Most likely its partner black is the switched-hot. The lamp will want this switched-hot, and actual neutral.
answered 3 hours ago
HarperHarper
73.6k448148
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
konyak is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f159929%2fwhy-is-a-white-electrical-wire-connected-to-2-black-wires%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
The cable with the white wire that's connected to the two black wires is a switch loop:
Normally wires with white insulation are used only for neutrals, but code makes an exception to allow for use of the white wire in a cable used as a switch loop as a hot rather than a neutral.
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
add a comment |
The cable with the white wire that's connected to the two black wires is a switch loop:
Normally wires with white insulation are used only for neutrals, but code makes an exception to allow for use of the white wire in a cable used as a switch loop as a hot rather than a neutral.
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
add a comment |
The cable with the white wire that's connected to the two black wires is a switch loop:
Normally wires with white insulation are used only for neutrals, but code makes an exception to allow for use of the white wire in a cable used as a switch loop as a hot rather than a neutral.
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
The cable with the white wire that's connected to the two black wires is a switch loop:
Normally wires with white insulation are used only for neutrals, but code makes an exception to allow for use of the white wire in a cable used as a switch loop as a hot rather than a neutral.
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
answered 3 hours ago
batsplatstersonbatsplatsterson
13.4k11640
13.4k11640
add a comment |
add a comment |
That is positional coding. It is very important data.
Wire colors in cable are standardized and do not vary. In any cable, if neutral is present, it must be the white. The most likely application for this is in a switch loop. If neutral is not present but an always-hot is, contemporary Code says white must be used for an always-hot. That's to make it easier to identify with a voltage tester. Newer code says white so used, must be marked with tape.
Once you have identified the neutral bundle (all white), a white in a non-neutral bundle is one of these. The fact this is in a lamp makes this most likely a switch loop.
Most likely its partner black is the switched-hot. The lamp will want this switched-hot, and actual neutral.
answered 3 hours ago
HarperHarper
73.6k448148
add a comment |
That is positional coding. It is very important data.
Wire colors in cable are standardized and do not vary. In any cable, if neutral is present, it must be the white. The most likely application for this is in a switch loop. If neutral is not present but an always-hot is, contemporary Code says white must be used for an always-hot. That's to make it easier to identify with a voltage tester. Newer code says white so used, must be marked with tape.
Once you have identified the neutral bundle (all white), a white in a non-neutral bundle is one of these. The fact this is in a lamp makes this most likely a switch loop.
Most likely its partner black is the switched-hot. The lamp will want this switched-hot, and actual neutral.
answered 3 hours ago
HarperHarper
73.6k448148
add a comment |
That is positional coding. It is very important data.
Wire colors in cable are standardized and do not vary. In any cable, if neutral is present, it must be the white. The most likely application for this is in a switch loop. If neutral is not present but an always-hot is, contemporary Code says white must be used for an always-hot. That's to make it easier to identify with a voltage tester. Newer code says white so used, must be marked with tape.
Once you have identified the neutral bundle (all white), a white in a non-neutral bundle is one of these. The fact this is in a lamp makes this most likely a switch loop.
Most likely its partner black is the switched-hot. The lamp will want this switched-hot, and actual neutral.
answered 3 hours ago
HarperHarper
73.6k448148
That is positional coding. It is very important data.
Wire colors in cable are standardized and do not vary. In any cable, if neutral is present, it must be the white. The most likely application for this is in a switch loop. If neutral is not present but an always-hot is, contemporary Code says white must be used for an always-hot. That's to make it easier to identify with a voltage tester. Newer code says white so used, must be marked with tape.
Once you have identified the neutral bundle (all white), a white in a non-neutral bundle is one of these. The fact this is in a lamp makes this most likely a switch loop.
Most likely its partner black is the switched-hot. The lamp will want this switched-hot, and actual neutral.
answered 3 hours ago
HarperHarper
73.6k448148
answered 3 hours ago
HarperHarper
73.6k448148
answered 3 hours ago
HarperHarper
73.6k448148
answered 3 hours ago
HarperHarper
73.6k448148
73.6k448148
add a comment |
add a comment |
konyak is a new contributor. Be nice, and check out our Code of Conduct.
konyak is a new contributor. Be nice, and check out our Code of Conduct.
konyak is a new contributor. Be nice, and check out our Code of Conduct.
konyak is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f159929%2fwhy-is-a-white-electrical-wire-connected-to-2-black-wires%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
