High current, low voltage capacitors












1












$begingroup$


I'm putting together a high current (200A+), low voltage (<5v) rectifier circuit.



I have sufficient bridge rectifiers, but to smooth out the waveform I need a strong enough capacitor bank. Besides opting for capacitors rated at a voltage of 10vdc (double the 5v just to be safe), what other stats or capacitor specs should I be looking for? Just get three one with the highest max operating temperature? The AC wave will be 50hz.






capacitor high-current bridge-rectifier







share|improve this question









$endgroup$








  • 3




    $begingroup$
    Low-voltage high-amperage power sources are not designed as plain AC rectifiers. They are made as "AC-DC converters", where AC gets rectified to high-voltage DC, the DC gets converted into high-frequency "chopped" signal, and then transformed into low-voltage, and then rectified using synchronous active rectifiers. The smoothing caps then operate at a very high frequency and don't need to be of extremely high values. You need to seriously reconsider your design approach, unless you are making some welding apparatus.
    $endgroup$
    – Ale..chenski
    4 hours ago








  • 1




    $begingroup$
    In addition to what Ale..chenski said, you have discovered that at high currents and low frequency you need an unreasonable amount of smoothing capacitance since the charge consumed is so high but the refresh rate is so low. The ripple will be enormous even with massive caps. Refresh a few thousand times faster and your capacitors can be a few thousand times smaller. Capacitors have a limit on ripple current anyways and such high currents and low frequencies will produce enormous ripple currents that will overheat and blow caps.
    $endgroup$
    – Toor
    4 hours ago












  • $begingroup$
    what is your ripple spec 10% V? with 200A RMS
    $endgroup$
    – Sunnyskyguy EE75
    2 hours ago








  • 1




    $begingroup$
    @SunnyskyguyEE75 haven't considered that, just want to minimise what ripple there is. If it's not worth the effort, I may just leave it as AC. The purpose is to heat a piece of carbon or stainless to serve as a heating element. Was considering rectifying the AC signal to minimise any eddy currents.
    $endgroup$
    – Chris
    2 hours ago






  • 1




    $begingroup$
    You can use a 6V 700A CCA lead acid battery
    $endgroup$
    – Sunnyskyguy EE75
    1 hour ago


















1












$begingroup$


I'm putting together a high current (200A+), low voltage (<5v) rectifier circuit.



I have sufficient bridge rectifiers, but to smooth out the waveform I need a strong enough capacitor bank. Besides opting for capacitors rated at a voltage of 10vdc (double the 5v just to be safe), what other stats or capacitor specs should I be looking for? Just get three one with the highest max operating temperature? The AC wave will be 50hz.






capacitor high-current bridge-rectifier







share|improve this question









$endgroup$








  • 3




    $begingroup$
    Low-voltage high-amperage power sources are not designed as plain AC rectifiers. They are made as "AC-DC converters", where AC gets rectified to high-voltage DC, the DC gets converted into high-frequency "chopped" signal, and then transformed into low-voltage, and then rectified using synchronous active rectifiers. The smoothing caps then operate at a very high frequency and don't need to be of extremely high values. You need to seriously reconsider your design approach, unless you are making some welding apparatus.
    $endgroup$
    – Ale..chenski
    4 hours ago








  • 1




    $begingroup$
    In addition to what Ale..chenski said, you have discovered that at high currents and low frequency you need an unreasonable amount of smoothing capacitance since the charge consumed is so high but the refresh rate is so low. The ripple will be enormous even with massive caps. Refresh a few thousand times faster and your capacitors can be a few thousand times smaller. Capacitors have a limit on ripple current anyways and such high currents and low frequencies will produce enormous ripple currents that will overheat and blow caps.
    $endgroup$
    – Toor
    4 hours ago












  • $begingroup$
    what is your ripple spec 10% V? with 200A RMS
    $endgroup$
    – Sunnyskyguy EE75
    2 hours ago








  • 1




    $begingroup$
    @SunnyskyguyEE75 haven't considered that, just want to minimise what ripple there is. If it's not worth the effort, I may just leave it as AC. The purpose is to heat a piece of carbon or stainless to serve as a heating element. Was considering rectifying the AC signal to minimise any eddy currents.
    $endgroup$
    – Chris
    2 hours ago






  • 1




    $begingroup$
    You can use a 6V 700A CCA lead acid battery
    $endgroup$
    – Sunnyskyguy EE75
    1 hour ago
















1












1








1





$begingroup$


I'm putting together a high current (200A+), low voltage (<5v) rectifier circuit.



I have sufficient bridge rectifiers, but to smooth out the waveform I need a strong enough capacitor bank. Besides opting for capacitors rated at a voltage of 10vdc (double the 5v just to be safe), what other stats or capacitor specs should I be looking for? Just get three one with the highest max operating temperature? The AC wave will be 50hz.






capacitor high-current bridge-rectifier







share|improve this question









$endgroup$




I'm putting together a high current (200A+), low voltage (<5v) rectifier circuit.



I have sufficient bridge rectifiers, but to smooth out the waveform I need a strong enough capacitor bank. Besides opting for capacitors rated at a voltage of 10vdc (double the 5v just to be safe), what other stats or capacitor specs should I be looking for? Just get three one with the highest max operating temperature? The AC wave will be 50hz.






capacitor high-current bridge-rectifier




capacitor high-current bridge-rectifier






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked 4 hours ago









ChrisChris

244




244








  • 3




    $begingroup$
    Low-voltage high-amperage power sources are not designed as plain AC rectifiers. They are made as "AC-DC converters", where AC gets rectified to high-voltage DC, the DC gets converted into high-frequency "chopped" signal, and then transformed into low-voltage, and then rectified using synchronous active rectifiers. The smoothing caps then operate at a very high frequency and don't need to be of extremely high values. You need to seriously reconsider your design approach, unless you are making some welding apparatus.
    $endgroup$
    – Ale..chenski
    4 hours ago








  • 1




    $begingroup$
    In addition to what Ale..chenski said, you have discovered that at high currents and low frequency you need an unreasonable amount of smoothing capacitance since the charge consumed is so high but the refresh rate is so low. The ripple will be enormous even with massive caps. Refresh a few thousand times faster and your capacitors can be a few thousand times smaller. Capacitors have a limit on ripple current anyways and such high currents and low frequencies will produce enormous ripple currents that will overheat and blow caps.
    $endgroup$
    – Toor
    4 hours ago












  • $begingroup$
    what is your ripple spec 10% V? with 200A RMS
    $endgroup$
    – Sunnyskyguy EE75
    2 hours ago








  • 1




    $begingroup$
    @SunnyskyguyEE75 haven't considered that, just want to minimise what ripple there is. If it's not worth the effort, I may just leave it as AC. The purpose is to heat a piece of carbon or stainless to serve as a heating element. Was considering rectifying the AC signal to minimise any eddy currents.
    $endgroup$
    – Chris
    2 hours ago






  • 1




    $begingroup$
    You can use a 6V 700A CCA lead acid battery
    $endgroup$
    – Sunnyskyguy EE75
    1 hour ago
















  • 3




    $begingroup$
    Low-voltage high-amperage power sources are not designed as plain AC rectifiers. They are made as "AC-DC converters", where AC gets rectified to high-voltage DC, the DC gets converted into high-frequency "chopped" signal, and then transformed into low-voltage, and then rectified using synchronous active rectifiers. The smoothing caps then operate at a very high frequency and don't need to be of extremely high values. You need to seriously reconsider your design approach, unless you are making some welding apparatus.
    $endgroup$
    – Ale..chenski
    4 hours ago








  • 1




    $begingroup$
    In addition to what Ale..chenski said, you have discovered that at high currents and low frequency you need an unreasonable amount of smoothing capacitance since the charge consumed is so high but the refresh rate is so low. The ripple will be enormous even with massive caps. Refresh a few thousand times faster and your capacitors can be a few thousand times smaller. Capacitors have a limit on ripple current anyways and such high currents and low frequencies will produce enormous ripple currents that will overheat and blow caps.
    $endgroup$
    – Toor
    4 hours ago












  • $begingroup$
    what is your ripple spec 10% V? with 200A RMS
    $endgroup$
    – Sunnyskyguy EE75
    2 hours ago








  • 1




    $begingroup$
    @SunnyskyguyEE75 haven't considered that, just want to minimise what ripple there is. If it's not worth the effort, I may just leave it as AC. The purpose is to heat a piece of carbon or stainless to serve as a heating element. Was considering rectifying the AC signal to minimise any eddy currents.
    $endgroup$
    – Chris
    2 hours ago






  • 1




    $begingroup$
    You can use a 6V 700A CCA lead acid battery
    $endgroup$
    – Sunnyskyguy EE75
    1 hour ago










3




3




$begingroup$
Low-voltage high-amperage power sources are not designed as plain AC rectifiers. They are made as "AC-DC converters", where AC gets rectified to high-voltage DC, the DC gets converted into high-frequency "chopped" signal, and then transformed into low-voltage, and then rectified using synchronous active rectifiers. The smoothing caps then operate at a very high frequency and don't need to be of extremely high values. You need to seriously reconsider your design approach, unless you are making some welding apparatus.
$endgroup$
– Ale..chenski
4 hours ago






$begingroup$
Low-voltage high-amperage power sources are not designed as plain AC rectifiers. They are made as "AC-DC converters", where AC gets rectified to high-voltage DC, the DC gets converted into high-frequency "chopped" signal, and then transformed into low-voltage, and then rectified using synchronous active rectifiers. The smoothing caps then operate at a very high frequency and don't need to be of extremely high values. You need to seriously reconsider your design approach, unless you are making some welding apparatus.
$endgroup$
– Ale..chenski
4 hours ago






1




1




$begingroup$
In addition to what Ale..chenski said, you have discovered that at high currents and low frequency you need an unreasonable amount of smoothing capacitance since the charge consumed is so high but the refresh rate is so low. The ripple will be enormous even with massive caps. Refresh a few thousand times faster and your capacitors can be a few thousand times smaller. Capacitors have a limit on ripple current anyways and such high currents and low frequencies will produce enormous ripple currents that will overheat and blow caps.
$endgroup$
– Toor
4 hours ago






$begingroup$
In addition to what Ale..chenski said, you have discovered that at high currents and low frequency you need an unreasonable amount of smoothing capacitance since the charge consumed is so high but the refresh rate is so low. The ripple will be enormous even with massive caps. Refresh a few thousand times faster and your capacitors can be a few thousand times smaller. Capacitors have a limit on ripple current anyways and such high currents and low frequencies will produce enormous ripple currents that will overheat and blow caps.
$endgroup$
– Toor
4 hours ago














$begingroup$
what is your ripple spec 10% V? with 200A RMS
$endgroup$
– Sunnyskyguy EE75
2 hours ago






$begingroup$
what is your ripple spec 10% V? with 200A RMS
$endgroup$
– Sunnyskyguy EE75
2 hours ago






1




1




$begingroup$
@SunnyskyguyEE75 haven't considered that, just want to minimise what ripple there is. If it's not worth the effort, I may just leave it as AC. The purpose is to heat a piece of carbon or stainless to serve as a heating element. Was considering rectifying the AC signal to minimise any eddy currents.
$endgroup$
– Chris
2 hours ago




$begingroup$
@SunnyskyguyEE75 haven't considered that, just want to minimise what ripple there is. If it's not worth the effort, I may just leave it as AC. The purpose is to heat a piece of carbon or stainless to serve as a heating element. Was considering rectifying the AC signal to minimise any eddy currents.
$endgroup$
– Chris
2 hours ago




1




1




$begingroup$
You can use a 6V 700A CCA lead acid battery
$endgroup$
– Sunnyskyguy EE75
1 hour ago






$begingroup$
You can use a 6V 700A CCA lead acid battery
$endgroup$
– Sunnyskyguy EE75
1 hour ago












1 Answer
1






active

oldest

votes


















2












$begingroup$

First make a rough spec for ripple from C and ESR.



For $C=I_C*dt/dV$

with Vc=5V and let ripple=5% or dV=250mV(pp) and dt= 10ms ( 100Hz) with Ic=200A



$C=200A*10ms/250V=8mF$

let dV=2% 100mV from cap

ESR=V/ESR=0.1V/200A=500 μΩ



For a total ripple of 250mV+100mV=350mVpp



ESR*C=T= 500 μΩ * 8mF = 4 μs



Now check Electric Double Layer Capacitors (EDLC), Supercapacitors specs. anything close rated for >5V



enter image description here
8.2uF 50mΩ TOO HIGH by 100x even at $16



Now you know this concept is going to be more expensive than a 1kW PC SMPS PSU.






share|improve this answer









$endgroup$













    Your Answer





    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("mathjaxEditing", function () {
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
    });
    });
    }, "mathjax-editing");

    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("schematics", function () {
    StackExchange.schematics.init();
    });
    }, "cicuitlab");

    StackExchange.ready(function() {
    var channelOptions = {
    tags: "".split(" "),
    id: "135"
    };
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function() {
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled) {
    StackExchange.using("snippets", function() {
    createEditor();
    });
    }
    else {
    createEditor();
    }
    });

    function createEditor() {
    StackExchange.prepareEditor({
    heartbeatType: 'answer',
    autoActivateHeartbeat: false,
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader: {
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    },
    onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    });


    }
    });














    draft saved

    draft discarded


















    StackExchange.ready(
    function () {
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f423103%2fhigh-current-low-voltage-capacitors%23new-answer', 'question_page');
    }
    );

    Post as a guest















    Required, but never shown

























    1 Answer
    1






    active

    oldest

    votes








    1 Answer
    1






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes









    2












    $begingroup$

    First make a rough spec for ripple from C and ESR.



    For $C=I_C*dt/dV$

    with Vc=5V and let ripple=5% or dV=250mV(pp) and dt= 10ms ( 100Hz) with Ic=200A



    $C=200A*10ms/250V=8mF$

    let dV=2% 100mV from cap

    ESR=V/ESR=0.1V/200A=500 μΩ



    For a total ripple of 250mV+100mV=350mVpp



    ESR*C=T= 500 μΩ * 8mF = 4 μs



    Now check Electric Double Layer Capacitors (EDLC), Supercapacitors specs. anything close rated for >5V



    enter image description here
    8.2uF 50mΩ TOO HIGH by 100x even at $16



    Now you know this concept is going to be more expensive than a 1kW PC SMPS PSU.






    share|improve this answer









    $endgroup$


















      2












      $begingroup$

      First make a rough spec for ripple from C and ESR.



      For $C=I_C*dt/dV$

      with Vc=5V and let ripple=5% or dV=250mV(pp) and dt= 10ms ( 100Hz) with Ic=200A



      $C=200A*10ms/250V=8mF$

      let dV=2% 100mV from cap

      ESR=V/ESR=0.1V/200A=500 μΩ



      For a total ripple of 250mV+100mV=350mVpp



      ESR*C=T= 500 μΩ * 8mF = 4 μs



      Now check Electric Double Layer Capacitors (EDLC), Supercapacitors specs. anything close rated for >5V



      enter image description here
      8.2uF 50mΩ TOO HIGH by 100x even at $16



      Now you know this concept is going to be more expensive than a 1kW PC SMPS PSU.






      share|improve this answer









      $endgroup$
















        2












        2








        2





        $begingroup$

        First make a rough spec for ripple from C and ESR.



        For $C=I_C*dt/dV$

        with Vc=5V and let ripple=5% or dV=250mV(pp) and dt= 10ms ( 100Hz) with Ic=200A



        $C=200A*10ms/250V=8mF$

        let dV=2% 100mV from cap

        ESR=V/ESR=0.1V/200A=500 μΩ



        For a total ripple of 250mV+100mV=350mVpp



        ESR*C=T= 500 μΩ * 8mF = 4 μs



        Now check Electric Double Layer Capacitors (EDLC), Supercapacitors specs. anything close rated for >5V



        enter image description here
        8.2uF 50mΩ TOO HIGH by 100x even at $16



        Now you know this concept is going to be more expensive than a 1kW PC SMPS PSU.






        share|improve this answer









        $endgroup$



        First make a rough spec for ripple from C and ESR.



        For $C=I_C*dt/dV$

        with Vc=5V and let ripple=5% or dV=250mV(pp) and dt= 10ms ( 100Hz) with Ic=200A



        $C=200A*10ms/250V=8mF$

        let dV=2% 100mV from cap

        ESR=V/ESR=0.1V/200A=500 μΩ



        For a total ripple of 250mV+100mV=350mVpp



        ESR*C=T= 500 μΩ * 8mF = 4 μs



        Now check Electric Double Layer Capacitors (EDLC), Supercapacitors specs. anything close rated for >5V



        enter image description here
        8.2uF 50mΩ TOO HIGH by 100x even at $16



        Now you know this concept is going to be more expensive than a 1kW PC SMPS PSU.







        share|improve this answer












        share|improve this answer



        share|improve this answer










        answered 2 hours ago









        Sunnyskyguy EE75Sunnyskyguy EE75

        66.6k22397




        66.6k22397






























            draft saved

            draft discarded




















































            Thanks for contributing an answer to Electrical Engineering Stack Exchange!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid …



            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.


            Use MathJax to format equations. MathJax reference.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function () {
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f423103%2fhigh-current-low-voltage-capacitors%23new-answer', 'question_page');
            }
            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            -

            Popular posts from this blog

            Costa Masnaga

            Image
            .mw-parser-output .avviso .mbox-text-div>div,.mw-parser-output .avviso .mbox-text-full-div>div{font-size:90%}.mw-parser-output .avviso .mbox-image div{width:52px}.mw-parser-output .avviso .mbox-text-full-div .hide-when-compact{display:block} Questa voce o sezione sull'argomento Lombardia non cita le fonti necessarie o quelle presenti sono insufficienti . Puoi migliorare questa voce aggiungendo citazioni da fonti attendibili secondo le linee guida sull'uso delle fonti. Segui i suggerimenti del progetto di riferimento. Costa Masnaga comune Localizzazione Stato   Italia Regione Lombardia Provincia Lecco Amministrazione Sindaco Sabina Panzeri (Al centro il cittadino) dall'08/06/2009 Territorio Coordinate 45°46′N 9°17′E  /  45.766667°N 9.283333°E 45.766667; 9.283333  ( Costa Masnaga ) Coordinate: 45°46′N 9°17′E  /  45.766667°N 9.283333°E 45.766667; 9.283333  ( Costa Masnaga ) Altitudine 318 m s.l.m...
            Read more

            Fotorealismo

            Image
            Guerrino Boatto, Venice's St. Barnaba Church and canal Il fotorealismo è un genere di pittura basato sull'uso di una o più fotografie dalle quali l'artista prende le informazioni necessarie da utilizzare poi nel processo della creazione dell'opera, in genere ad olio o ad acrilico, al fine di avere un aspetto finale il più simile possibile alla fotografia. Indice 1 Storia 2 Lista dei fotorealisti 3 Note 4 Voci correlate 5 Altri progetti Storia | Il fotorealismo è un movimento che nasce negli Stati Uniti d'America alla fine degli anni sessanta [1] sulla scia della Pop Art [2] [3] [4] , e insieme condividono il carattere reazionario verso la travolgente ascesa dei media, che alla metà del ventesimo secolo si trasforma in un fenomeno di massa talmente imponente da minacciare il valore dell'immagine nell'arte. [5] [6] Ne consegue così che, colto il gesto d'inizio che fu della Pop Art, i fotorealisti aprono ad un ...
            Read more

            Sidney Franklin

            Image
            Questa voce sull'argomento registi statunitensi è solo un abbozzo . Contribuisci a migliorarla secondo le convenzioni di Wikipedia. Sidney Franklin, foto di Carl Van Vechten Oscar alla memoria Irving G. Thalberg 1943 Sidney Franklin , all'anagrafe Sidney Arnold Franklin , (San Francisco, 21 marzo 1893 – Santa Monica, 18 maggio 1972), è stato un regista, produttore cinematografico e attore statunitense. Il 20 giugno 1963, si sposò con l'attrice australiana Enid Bennett. Il matrimonio durò fino alla morte dell'attrice, il 14 maggio 1969 [1] Indice 1 Filmografia 1.1 Regista 1.2 Aiuto regia (parziale) 1.3 Produttore 1.4 Attore (parziale) 2 Note 3 Altri progetti 4 Collegamenti esterni Filmografia | Regista | The Baby , co-regia Chester M. Franklin (1915) The Rivals , co-regia Chester M. Franklin (1915) Little Dick's First Case , co-regia Chester M. Franklin (1915) Her Filmland Hero , co-...
            Read more