What's wrong with my1943/5200 Mosfet Amplifier? Blown on first run
up vote
1
down vote
favorite
I have just brought an 1943/5200 mosfet based amplifier board. Shopkeeper said it's rated for 24-0-24 AC.
So I connected it with 24-0-24 transformer like this in image below.
As soon as I turned the power supply, I heard a loud hum from transformer, Like it was on full load. and few seconds later cap. on left side blown.
(I have also got a loud noise from my speakers also like I have passed 24VAC through em.)
I have no Idea why this happened. Did I made some mistake?
Is circuit is actuality meant for 24-0-24 DC?
What now? can I still revive my circuit? What are the components which might have died in the process? are my mosfet's are still okay?
mosfet circuit-analysis amplifier audio power-amplifier
asked 10 hours ago
GeekWithGlasses
1086
add a comment |
up vote
1
down vote
favorite
I have just brought an 1943/5200 mosfet based amplifier board. Shopkeeper said it's rated for 24-0-24 AC.
So I connected it with 24-0-24 transformer like this in image below.
As soon as I turned the power supply, I heard a loud hum from transformer, Like it was on full load. and few seconds later cap. on left side blown.
(I have also got a loud noise from my speakers also like I have passed 24VAC through em.)
I have no Idea why this happened. Did I made some mistake?
Is circuit is actuality meant for 24-0-24 DC?
What now? can I still revive my circuit? What are the components which might have died in the process? are my mosfet's are still okay?
mosfet circuit-analysis amplifier audio power-amplifier
asked 10 hours ago
GeekWithGlasses
1086
add a comment |
up vote
1
down vote
favorite
up vote
1
down vote
favorite
I have just brought an 1943/5200 mosfet based amplifier board. Shopkeeper said it's rated for 24-0-24 AC.
So I connected it with 24-0-24 transformer like this in image below.
As soon as I turned the power supply, I heard a loud hum from transformer, Like it was on full load. and few seconds later cap. on left side blown.
(I have also got a loud noise from my speakers also like I have passed 24VAC through em.)
I have no Idea why this happened. Did I made some mistake?
Is circuit is actuality meant for 24-0-24 DC?
What now? can I still revive my circuit? What are the components which might have died in the process? are my mosfet's are still okay?
mosfet circuit-analysis amplifier audio power-amplifier
asked 10 hours ago
GeekWithGlasses
1086
I have just brought an 1943/5200 mosfet based amplifier board. Shopkeeper said it's rated for 24-0-24 AC.
So I connected it with 24-0-24 transformer like this in image below.
As soon as I turned the power supply, I heard a loud hum from transformer, Like it was on full load. and few seconds later cap. on left side blown.
(I have also got a loud noise from my speakers also like I have passed 24VAC through em.)
I have no Idea why this happened. Did I made some mistake?
Is circuit is actuality meant for 24-0-24 DC?
What now? can I still revive my circuit? What are the components which might have died in the process? are my mosfet's are still okay?
mosfet circuit-analysis amplifier audio power-amplifier
mosfet circuit-analysis amplifier audio power-amplifier
asked 10 hours ago
GeekWithGlasses
1086
asked 10 hours ago
GeekWithGlasses
1086
asked 10 hours ago
GeekWithGlasses
1086
asked 10 hours ago
GeekWithGlasses
1086
asked 10 hours ago
GeekWithGlasses
1086
1086
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
up vote
4
down vote
accepted
That the amplifier needs a DC supply, not AC. The + G - is a strong give away. An AC power input would likely have a pair of ~ symbols.
Also an AC input would need at least a bridge rectifier and a big capacitor. I spot neither near the power supply connector.
answered 9 hours ago
Oldfart
7,7132825
what about damaged components? Will me mosfets be okay?
– GeekWithGlasses
9 hours ago
Impossible to say. With a bit of luck the capacitor somewhat limited the brunt.of the negative voltage.
– Oldfart
9 hours ago
add a comment |
up vote
1
down vote
24Vac would not be marked by “+” and “-“ on a circuit board or schematic. Furthermore it would not be specified as 24-0-24 either. Either your shopkeeper was mistaken or you misunderstood him.
That looks like a DC connection probably expecting +24, -24, and Gnd. That capacitor seems to be across the input supply. It is a polarized capacitor so it will fail on AC (you should check maximum voltage specification on it).
It is impossible to know what else might have failed under those conditions.
answered 9 hours ago
Edgar Brown
2,894422
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f412413%2fwhats-wrong-with-my1943-5200-mosfet-amplifier-blown-on-first-run%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
4
down vote
accepted
That the amplifier needs a DC supply, not AC. The + G - is a strong give away. An AC power input would likely have a pair of ~ symbols.
Also an AC input would need at least a bridge rectifier and a big capacitor. I spot neither near the power supply connector.
answered 9 hours ago
Oldfart
7,7132825
what about damaged components? Will me mosfets be okay?
– GeekWithGlasses
9 hours ago
Impossible to say. With a bit of luck the capacitor somewhat limited the brunt.of the negative voltage.
– Oldfart
9 hours ago
add a comment |
up vote
4
down vote
accepted
That the amplifier needs a DC supply, not AC. The + G - is a strong give away. An AC power input would likely have a pair of ~ symbols.
Also an AC input would need at least a bridge rectifier and a big capacitor. I spot neither near the power supply connector.
answered 9 hours ago
Oldfart
7,7132825
what about damaged components? Will me mosfets be okay?
– GeekWithGlasses
9 hours ago
Impossible to say. With a bit of luck the capacitor somewhat limited the brunt.of the negative voltage.
– Oldfart
9 hours ago
add a comment |
up vote
4
down vote
accepted
up vote
4
down vote
accepted
That the amplifier needs a DC supply, not AC. The + G - is a strong give away. An AC power input would likely have a pair of ~ symbols.
Also an AC input would need at least a bridge rectifier and a big capacitor. I spot neither near the power supply connector.
answered 9 hours ago
Oldfart
7,7132825
That the amplifier needs a DC supply, not AC. The + G - is a strong give away. An AC power input would likely have a pair of ~ symbols.
Also an AC input would need at least a bridge rectifier and a big capacitor. I spot neither near the power supply connector.
answered 9 hours ago
Oldfart
7,7132825
answered 9 hours ago
Oldfart
7,7132825
answered 9 hours ago
Oldfart
7,7132825
answered 9 hours ago
Oldfart
7,7132825
7,7132825
what about damaged components? Will me mosfets be okay?
– GeekWithGlasses
9 hours ago
Impossible to say. With a bit of luck the capacitor somewhat limited the brunt.of the negative voltage.
– Oldfart
9 hours ago
add a comment |
what about damaged components? Will me mosfets be okay?
– GeekWithGlasses
9 hours ago
Impossible to say. With a bit of luck the capacitor somewhat limited the brunt.of the negative voltage.
– Oldfart
9 hours ago
what about damaged components? Will me mosfets be okay?
– GeekWithGlasses
9 hours ago
what about damaged components? Will me mosfets be okay?
– GeekWithGlasses
9 hours ago
Impossible to say. With a bit of luck the capacitor somewhat limited the brunt.of the negative voltage.
– Oldfart
9 hours ago
Impossible to say. With a bit of luck the capacitor somewhat limited the brunt.of the negative voltage.
– Oldfart
9 hours ago
add a comment |
up vote
1
down vote
24Vac would not be marked by “+” and “-“ on a circuit board or schematic. Furthermore it would not be specified as 24-0-24 either. Either your shopkeeper was mistaken or you misunderstood him.
That looks like a DC connection probably expecting +24, -24, and Gnd. That capacitor seems to be across the input supply. It is a polarized capacitor so it will fail on AC (you should check maximum voltage specification on it).
It is impossible to know what else might have failed under those conditions.
answered 9 hours ago
Edgar Brown
2,894422
add a comment |
up vote
1
down vote
24Vac would not be marked by “+” and “-“ on a circuit board or schematic. Furthermore it would not be specified as 24-0-24 either. Either your shopkeeper was mistaken or you misunderstood him.
That looks like a DC connection probably expecting +24, -24, and Gnd. That capacitor seems to be across the input supply. It is a polarized capacitor so it will fail on AC (you should check maximum voltage specification on it).
It is impossible to know what else might have failed under those conditions.
answered 9 hours ago
Edgar Brown
2,894422
add a comment |
up vote
1
down vote
up vote
1
down vote
24Vac would not be marked by “+” and “-“ on a circuit board or schematic. Furthermore it would not be specified as 24-0-24 either. Either your shopkeeper was mistaken or you misunderstood him.
That looks like a DC connection probably expecting +24, -24, and Gnd. That capacitor seems to be across the input supply. It is a polarized capacitor so it will fail on AC (you should check maximum voltage specification on it).
It is impossible to know what else might have failed under those conditions.
answered 9 hours ago
Edgar Brown
2,894422
24Vac would not be marked by “+” and “-“ on a circuit board or schematic. Furthermore it would not be specified as 24-0-24 either. Either your shopkeeper was mistaken or you misunderstood him.
That looks like a DC connection probably expecting +24, -24, and Gnd. That capacitor seems to be across the input supply. It is a polarized capacitor so it will fail on AC (you should check maximum voltage specification on it).
It is impossible to know what else might have failed under those conditions.
answered 9 hours ago
Edgar Brown
2,894422
answered 9 hours ago
Edgar Brown
2,894422
answered 9 hours ago
Edgar Brown
2,894422
answered 9 hours ago
Edgar Brown
2,894422
2,894422
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f412413%2fwhats-wrong-with-my1943-5200-mosfet-amplifier-blown-on-first-run%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
